Glanz MH-124SD 12″ Tonearm

£13,995.00

An old Japanese name but newly returned to the UK – This is the ultimate level Glanz MH-124SD tonearm, available only in 12″ length, to order.  Like all Glanz tonearms, constructed from stainless steel parts but here with ‘diamond like carbon’ coating, and with even more obsessive attention to resonance control than the S Series arms.  Effective mass is in the order of 30g.  Shipped with a Glanz MH-4S headshell and a quality tonearm cable.

Available on back-order

SKU: GLANZ_SD Category:

Description

The “Jewel in the Crown” – the “premium” highest-grade model, acknowledged as delivering the most trusted performance.
Only available in this 12″ version.

• In pursuit of the ultimate tone arm for further enhanced performance, we have introduced features that take you beyond the S model, as follows:
• Approximately 30 parts are coated in DLC (Diamond-Like Carbon) – the sound rise is outstanding.
• With the addition of carbon fibre to the arm tube, even more powerful vibration prevention measures are applied
Furthermore, the arm tube uses a thin silver wire of low resistance, and silk roll is used for the coating of the flow line, ultimately damping it with vibration proof materials
• Around the weight, a quadruple damper system using different materials has been adopted, and vibration absorption is achieved over a wide range.


Design

The material of the main body is made of hard stainless steel. The process of machining has been extremely difficult, but as a result, but we are proud to say that the sound quality has reached an unparalleled level. If the fulcrum, which is essential for sound quality, is a weak structure, it will reverberate and directly impact the overall sound quality. In this design, the four large bearings are firmly supported, preventing resonance and shake, and enhancing tracing ability.  In particular, the lower bearing in the vertical axis uses a high-precision thrust bearing, giving a strut structure which allows the heavy arms to move with high sensitivity, greatly enhancing the tracking capability.

At the most important section of the arm tube with regards to impact on sound quality, vibration is controlled firstly with a layer of carbon fibre on the inside of the arm, followed by a layer of poly fibre on the inside of that. Next, the wire that transmits the electric signal is wrapped in silk thread using low resistance silver wire, and around all of this is the poly fibre, doubly ensuring that it is vibration-proof (for model SD).  The points where each part joins another are designed to be in tight surface contact to avoid using adhesive as much as possible. In particular, the assembly of the bearings requires meticulous sensitivity.

We took pains to ensure that the curvature of the arm did not exert any additional force. This is easier to understand if you imagine how an extra twisting force is applied by your hand when you manipulate an L-shaped rod rather than a straight one. On top of that, we placed “vibration absorbing structures” in the most suitable place, thereby effectively damping the resonance.

For the weight section we use different damper materials in 1, 2, 3 and 4 (for model SD), and these are constructed to absorb vibration over a wide area. The rubber material in 1 is firmly held in place by long screws, thus eliminating anxiety that it will become slack as it ages.  Heavy tungsten is embedded in the stainless steel material on the main weight so that the centre of gravity is closer to the fulcrum, and the stainless steel material and tungsten are closely bound with rubber material, which also absorbs vibration. (for model SD)

By making the headshell into a single structure through the scraping process, we were able to greatly reduce vibration loss. Moreover, by trimming away unnecessary material as much as possible, we have devised a weight reduction similar to that of aluminium (although the material is actually stainless steel), resulting in an extremely light structure that can firmly support the entire cartridge. Rubber in the S Model and carbon in the SD Model both absorb unnecessary signals in the upper part of the structure.  Because this slim design (just 10 mm in width, that can be supported near the very centre of the cartridge), can be connected directly to the centre point, the vibration loss is reduced and the sound quality is further improved.


Specification

 MODEL MH-124SD
BalancingStatic Balancing
Total Length (*1)340mm
Effective Length (*2) 305mm
Practical Length (*3) 290mm
Offset Angle20 °
Adaptable cartridge weight
(incl headshell)
 12~31g(40g)
Total weight1.12kg
Overhung15mm
Tracking weight range0.25g (Minimum scale) – over 6g
(3g/360 °rotation)
Adjustable height (*4)41~70mm
Headshell weight12g (Including screws and lead wires)
Shaft dimensions to mounting base16mmΦ
Mounting hole size30mmΦ
Fixing depth sizeUp to 20mm (Another size is available)

(*1) : From counter weight shaft end headshell terminal.
(*2) : From centre of tonearm Base to stylus tip.
(*3) : From centre of tonearm Base to centre of turntable)
(*4) : From plinth surface to horizontal height of arm tube

• MH-124SD 12″ price including 20% VAT £13,995.00 Including very high quality interconnect cable & MH-4S headshell
• Spare MH-4S headshell 13gm  £425.00

Reviews

There are no reviews yet.

Be the first to review “Glanz MH-124SD 12″ Tonearm”