Improved Mounting Collar for Jelco Tonearms – Grey

£51.00£53.25

SOLD OUT – new stocks due mid-November.  Our very popular Jelco mounting collar, in smart grey anodised finish to match grey Jelco arms (Jelco call grey ‘bronze’).  You can opt for a nylon-tipped grub screw for £2.25 extra (inc VAT) – this gives a nicer ‘feel’ than the standard flat ended steel grub screw, making it a little easier to secure the arm pillar with minimum force.  UK shipping included.

Clear

Description

Our custom improved mounting collars for Jelco tonearms have been re-designed in and are now even better and easier to use.   The Mk3 collar has rounded shoulders, but is otherwise identical to the Mk2.  Key improvements over our Mk1 collar include:

[list type=”check”]

  • The central pillar hole now has a sharp side-cutout.  This means that the arm pillar is now held gently, but firmly, against two vertical’knife edges’, so there is no longer any possibility of the arm pillar leaning to one side.  If your armboard and platter are aligned to the same level plane, this new collar will guarantee that the Jelco arm pillar will be truly vertical to that plane.
  • The standard grub screw is a large 6mm stainless steel item,  with a flat end stub.  A nylon-tipped grub screw can be specified at additional cost (£2.25 inc VAT).  The nylon tip grips the arm pillar better than the flat steel version, meaning that the arm height can be set using minimum force.  These nylon tipped screws are very expensive, which is why they are optional.  Expensive, yes, but worthwhile.
  • The overall diameter of the collar is now the same as the standard Jelco collar.  This means full compatibility with any armboard cut for a standard Jelco arm.

[/list]

Why do I need a different collar for my Jelco tonearm?

Have you ever tried to set the azimuth of a Jelco tonearm correctly?  Just when you think you’ve got it sorted, it’s off again!  That’s because the standard collar, while beautifully machined,  provides very poor vertical support of the arm pillar;  and the tiny set screw typically pushes the top part of the arm to one side, almost guaranteeing that the arm will not be properly set up. The azimuth actually varies as the arm traverses the record, which matters a great deal with modern cartridges and stylus profiles.  The custom collar gets around that problem by ensuring that the arm pillar will always be secured properly vertical, so setup becomes easy and repeatable.  That means better musical reproduction.

Is the collar compatible with other tonearms?

The collar is fully compatible with standard Jelco collar mounting templates, and all Jelco manufactured derivatives with 18mm diameter pillars, including Audioquest, LAD, Ortofon, Roksan.  Some Sumiko variants have a smaller 16mm pillar, so are not compatible.

Key Features

[list type=”check”]

  • The Improved collar is 5mm taller than the standard collar, and longer underneath for much better support of the arm pillar.
  • It is fitted as standard with a large stainless steel M6 grub screw, with flat end stub to protect the soft metal of the arm pillar.
  • A nylon-tipped grub screw is offered as an optional extra at £2.25 (inc VAT).  The nylon tip grips the arm pillar better than the flat steel version, meaning that the arm height can be set with minimum force.  These nylon tipped screws are very expensive, which is why they are optional.  Expensive, yes, but worthwhile.
  • Supplied with a hex key for grub screw adjustment, and stainless steel fixings consisting of 25mm long M4 bolts with nuts and washers and hex key for arm height adjustment.  If you have a thick armboard and need longer mounting bolts (40mm, 50mm and 60mm bolts are available), these can be supplied at no additional cost

[/list]

Application Notes

The custom collar is 5mm taller above the armboard than the Jelco original.  Look carefully at your tonearm as it’s currently fitted to the turntable – if there is less than 5mm clearance between the top of the standard Jelco collar and the base of the arm rest plate as currently fitted to your record deck, it may not be possible to set the arm low enough with the custom collar, to achieve correct VTA, without recourse to a thicker platter mat or headshell spacers.  It is possible to use thin metal shims between the cartridge and headshell to tilt the rear of the cartridge down a touch, thereby achieving the correct VTA without using different mats or spacers.    Please ask us if you are unsure about this.  In practice, the potential problem only applies to turntables with very low-profile platters, eg the Technics SL-1200; however suitable and compatible armboards are available for the SL-1200 from online sellers which allow the whole arm to be sunk low enough to ensure that correct VTA is achievable without any difficulty. We recommend those sold by eBay seller f1sport.

A matching 10mm spacer ring is available immediately, also in grey and black, at £19 including UK VAT – it is designed to raise the whole tonearm higher to accommodate really tall turntable platters, such as stacked platter Lencos.  The spacer ring is fully compatible with the standard Jelco collar.

 

 

What Length Bolts Do I Need to Mount a Collar On My Deck?

Please note that only 25mm bolts have full threads – please refer to the product images above, and choose the optimum bolt length carefully using this table:

Depth (Thickness) of Armboard

Collar

Collar + Spacer Rings

1 Ring

2 Rings

Up to 12mm Depth

25mm

40mm

60mm

12mm-25mm Depth

40mm

60mm

60mm

25mm-45mm Depth

60mm

70mm*

80mm*

45-60mm Depth

80mm*

90mm*

100mm*

*we don’t supply bolts longer than 60mm

Additional information

Bolt Length

, ,

Nylon-Tipped Grub Screw

No, Yes

Reviews

There are no reviews yet.

Be the first to review “Improved Mounting Collar for Jelco Tonearms – Grey”

Your email address will not be published. Required fields are marked *